摘要
本设计说明书包括三部分,第一部分为冲压模具设计,包括有零件的工艺分析﹑模具结构形式的比较﹑有关工艺的计算﹑模具强度的校核﹑压力中心的求算等方面的计算;第二部分为方形﹑圆形和环形热压模具设计,也包括有模具材料分析﹑零件工艺性能分析﹑模具结构形式选择﹑模具强度校核﹑压力中心的求算等方面的计算。第三部分为结束语和致谢词。
[关键词] 插口封条 冲压模具 热压模具 模具设计
Abstract
The manual of the design include three parts, the first part for washing press the molding tool design, and it includes the analyze of the craft of the spare parts﹑ the form's comparison of the molding tool construction﹑ the calculation of the craft﹑ the strength's of the molding ﹑the calculation of the pressure to the center, and so on. The second part is the design of molding about to a square ﹑ a circular and a round part, and also include the analyze of the material for molding﹑ the analyze of the craft about part﹑the choice of form for mold﹑ the strength's of the mold ﹑the calculation of the pressure to the center .. the third part is the tag and send thanks the phrase.
[Key words] the seal of faucet pressing mold the mold of that pressed in heating
the design of mold
目录
第一部分 计算机机箱插口冲压模具设计
第一章 零件形状及尺寸要求 1
第二章 零件材料性能分析… 1
第三章 有关模具结构形式的选择…………… 1
第四章 几种方案的比较…… 2
第五章 有关工艺的计算…… 3
1 毛坯尺寸的计算…… 3
(1)弯曲件毛坯长度的计算………… 3
(2)搭边值的确定… 3
(3)条料长度的计算 4
2 计算排样…………… 4
3 计算材料的利用率… 5
4 冲裁力、卸料力、推件力、弯曲力计算及初选压力机 6
5 冲裁模间隙及凹模、凸模刃口尺寸计算……………… 8
6 卸料弹簧的选择…… 12
7 选择上下模板及模柄 13
8 挡料销、始用挡料销的选择………… 13
9 垫板、凸模固定板的设计…………… 13
10 闭合高度……………14
11 导柱、导套…………14
12 卸料螺钉……………15
13 模具压力中心的计算……………… 16
14 凸、凹模强度的校核……………… 22
(1)凹模外形尺寸的确定及校核… 22
(2)凸模外形尺寸及强度校核…… 23
第六章 绘制模具结构总图及零件图(见各图纸)
第二部分 方形、圆形和环形热压模具设计
第七章 模具材料(三高石墨)的性能……… 27
第八章 粉末材料(MoSi2粉)性能指标…… 28
第九章 方形零件热压模具设计…………… 28
1 零件尺寸及要求…… 28
2 零件工艺性分析及压力机性能参数… 29
3 模具结构形式的确定 29
4 压制过程中力的计算 29
(1)压制压力………29
(2)侧压力和剩余侧压力……………30
(3)脱模压力………31
5 模具尺寸及精度…… 31
(1)阴模尺寸的确定……………… 32
(2)上模冲尺寸的确定…………… 32
(3)下模冲尺寸的确定…………… 33
(4)垫片尺寸…… 34
6 压力中心的计算…… 34
7 阴模强度与刚度的计算……………… 34
8 绘制模具结构总图及零件图(见各图纸)
第十章 圆形零件热压模具设计…………… 35
1 零件尺寸及要求…… 35
2 压力中心的计算…… 35
3 压制过程中力的计算 35
4 模具尺寸的确定…… 36
(1)阴模尺寸的确定……………… 36
(2)上模冲尺寸的确定…………… 37
(3)下模冲尺寸的确定…………… 38
(4)垫板、芯棒尺寸的确定……… 38
5 阴模强度与刚度的计算……………… 39
6 绘制模具结构总图及零件图(见各图纸)
第十一章 环形零件热压模具设计………… 39
1 零件尺寸及要求…… 39
2 模具尺寸的确定…… 40
(1)阴模尺寸的确定……………… 40
(2)上模冲尺寸的确定…………… 40
(3)下模冲尺寸的确定…………… 41
(4)垫片、芯棒尺寸的确定……… 41
3 压力中心的计算…… 42
4 压制过程中力的计算 45
5 阴模强度及刚度的计算…………… 45
6 绘制模具结构总图及零件图(见各图纸)
第三部分 结束语及致谢词………… 47